Single-Channel Modular Power Amplifier, 50 W, 70 V
Provides a professional amplifier solution for commercial applications that saves energy, space, and money. Unique modular design is super easy to configure and ships with everything required to enable surface mounting, rack mounting, and ganging multiple units together.
The Crestron AMP-150-70 is a space saving, energy efficient, commercial grade amplifier solution that’s totally configurable yet remarkably straightforward. Crestron® modular amps are simple to specify and install in any configuration.
All‑Inclusive Modular Design
The AMP-150-70 is a Hi‑Z modular amplifier housed in a quarter-width rack-mountable form factor that can be installed individually or ganged together in a single rack space. The AMP-150-70 ships with all the hardware required for installation of the unit by itself or in combination with any other unit(s). Rack and surface mount kits are included, so there are no other mounting accessories or rack shelves to purchase.
70 V Output
The AMP-150-70 is a single channel amplifier, conservatively rated at 50 W per channel, with a Hi‑Z output to drive a distributed speaker system. The AMP-150-70 has a 70 V output. Output wiring is facilitated using a detachable terminal block. Balanced and unbalanced inputs are provided for connection to a mono or stereo (summed) source via a detachable terminal block or RCA connectors.
Solid & Efficient Performance
The AMP-150-70 is engineered to deliver exceptional performance and reliability with low distortion, low noise, and high power headroom. Advanced Class D technology maximizes efficiency to reduce power consumption and heat dissipation. An internal universal power supply with power factor correction ensures consistent performance at varying line voltages.
Convection Cooled
The ultra‑efficient design of the AMP-150-70 ensures cool running operation without the use of internal fans. This means there’s no fan noise and no moving parts to break down. Cool operation also helps to ensure long term reliability. The AMP-150-70 is high‑density stackable with other Crestron modular amps, allowing multiple amplifiers to be installed vertically in an equipment rack without extra ventilation space in between.
Fully Protected
The AMP-150-70 features comprehensive protection against overheating, shorted or overloaded speaker lines, excessive input signals, and other faults. Built‑in clip limiting prevents extreme output signals and distortion that can damage the speakers or amplifier. In the case of a shorted speaker line or overheating condition, the output mutes automatically until the fault condition is resolved. In the event of a prolonged fault, such as an internal component failure, the output mutes instantly and the amplifier shuts down.
ENERGY STAR® Certified
Its energy‑efficient design enables the AMP-150-70 to meet demanding ENERGY STAR requirements. Crestron modular amps, like the AMP-150-70, allow organizations to fulfill their green initiatives without compromising on audio performance. In addition to its high efficiency under operation, the AMP-150-70 draws no added inrush current during power‑up, thereby reducing AC circuit requirements and allowing multiple units to be connected to a single switched circuit.
Key Features
- ENERGY STAR® certified power amplifier
- Ultra‑efficient space‑saving design
- 70 V output
- Single channel, 50 W
- Quarter‑width, 1 RU form factor
- Surface or rack mountable
- Gangable with other Crestron® modular amps
- All mounting and ganging hardware included
- High‑density stackable
- Convection cooling — no mechanical fans
- Comprehensive fault and speaker protection
- Clip limiter
- Low noise, low distortion, high headroom
- Low power consumption
- Balanced and unbalanced inputs
- Detachable terminal blocks for easy servicing
- Front panel level adjustment with tamper‑preventive magnetic cover
- Front panel power, fault, and signal/clip indicators
- Internal universal 100‑240 V power supply
| Audio |
| Input Signal Types |
Balanced or unbalanced analog line‑level |
| Output Power |
50 W @ 70 V nominal |
| Frequency Response |
200 Hz to 20 kHz ±0.5 dB |
| High‑Pass Filter |
‑3 dB @ 80 Hz, 12 dB per octave |
| THD+N |
<0.1%1 |
| S/N Ratio |
>100 dBA, 20 Hz to 20 kHz, balanced |
| Input Sensitivity |
1.23 Vrms, +4 dBu balanced;
0.316 Vrms, ‑10 dBV unbalanced;
For full rated output power |
| Protection |
Clip limiter, over current, under voltage, over temperature, DC offset, extreme high frequency |
| Connectors |
| SPEAKER OUT |
(1) 2‑pin 7.62 mm reversed gender 20 A detachable terminal block; Power amplifier output;
Wire Size: Terminals accept up to 12 AWG (3.31 mm2)
Note: Output is direct‑coupled, not transformer isolated |
| AUDIO IN L/R (unbalanced) |
(2) RCA connectors, female;
Unbalanced line‑level audio inputs (summed);
Maximum Input Level: 2.24 Vrms, +7 dBV (+9.2 dBu) |
| AUDIO IN L/R (balanced) |
(1) 5‑pin 3.5 mm detachable terminal block;
Balanced line‑level audio inputs (summed);
Maximum Input Level: 7.75 Vrms, +20 dBu;
Input Impedance: 20k Ohms |
| G |
(1) 6‑32 screw;
Chassis ground lug |
| 100‑240V~1A 50/60 Hz |
(1) IEC 60320 C14 main power inlet;
Mates with removable power cord, included |
| Controls & Indicators |
| PWR |
(1) Green LED, indicates operating power supplied from AC line power |
| FAULT |
(1) Red LED; indicates an over‑temperature or over‑current fault |
| SIGNAL |
(1) Bi‑color green/red LED, green indicates input signal presence and red indicates input signal clipping |
| Input Level |
(1) Screwdriver‑adjustable rotary control, adjusts the input attenuation level, tamper‑preventive magnetic cover included |
| Power |
| Main Power |
1 A @ 100‑240 VAC, 50/60 Hz |
| Power Consumption |
17 W, channel driven at 1/8th output power;
8 W, idle |
| Environmental |
| Temperature |
41° to 104° F (5° to 40° C) |
| Humidity |
10% to 90% RH (non‑condensing) |
| Construction |
| Chassis |
Metal, convection‑cooled (fanless), vented front and rear |
| Front Panel |
Metal, black finish with polycarbonate label overlay |
| Mounting |
Freestanding, surface‑mount, or 1/4‑width 1 RU 19 in. rack‑mountable; gangable with other Crestron modular AMP series products (adhesive feet, surface mounting kit, ganging kit, and rack mounting kit included) |
| Dimensions |
| Height |
1.74 in. (45 cm) without feet;
1.82 in. (47 mm) with surface kit |
| Width |
4.33 in. (110 mm);
5.43 in. (138 mm) with surface kit;
19.00 in. (483 mm) with rack kit |
| Depth |
10.46 in. (266 mm) |
| Compliance |
| ENERGY STAR, ErP (1275/2008/EC), UL 60065, FCC Class A commercial use |
Click
here to search product certificates.
Please select your region below to see the appropriate Advertised Pricing.