Online Help

Products

    Pages

        Master Photo: DM-TX-4KZ-100-C-1G-B-T (Faceplate Not Included)
        Add to Favorites

        DM-TX-4KZ-100-C-1G-B-T

        DigitalMedia 8G+® 4K60 4:4:4 HDR Wall Plate Transmitter, Black

        Provides a 1-gang mountable interface for an HD or 4K source as part of a complete DigitalMedia™ system. Supports 4K60 4:4:4 and HDR video signals. Connects to the DM 8G+® input of a DM® switcher or receiver via a single CATx cable. Includes IR and RS-232 control ports. Black finish.

        Faceplate not included

        Have a question?
        Add to a Project
        Find a Dealer

        The DM-TX-4KZ-100-C-1G wall plate transmitter provides a cost-effective solution for a single AV source as part of a complete Crestron® DigitalMedia™ system. Functioning as a DM 8G+® transmitter and control interface, the DM-TX-4KZ-100-C-1G provides an HDMI® input and a DM 8G+ output as well as IR and RS-232 control ports. The DM-TX-4KZ-100-C-1G incorporates DM 4KZ technology, which enables 4K60 4:4:4 and HDR (High Dynamic Range) support.1 The DM-TX-4KZ-100-C-1G is also compatible with HDBaseT® technology.

        The DM-TX-4KZ-100-C-1G provides a 1‑gang mountable design and is available in black (DM-TX-4KZ-100-C-1G-B-T) and white (DM-TX-4KZ-100-C-1G-W-T).

        4K60 4:4:4 and HDR Support
        DM 4KZ technology uses VESA® Display Stream Compression (DSC) to handle the extreme bandwidth requirement of resolutions beyond 4K30 4:4:4 and 4K60 4:2:0. DSC is a lightweight, line-based 2:1 compression standard that delivers visually lossless performance for 4K60 4:4:4 and HDR signals.1 DSC is applied only to 4K60 4:4:4 and HDR input signals. All other signals are transported uncompressed.

        An existing 4K DigitalMedia system can be upgraded to handle 4K60 4:4:4 and HDR video with the installation of DM 4KZ cards, transmitters, and receivers. The upgrade can be accomplished without the need to replace wiring or switchers. The DM-TX-4KZ-100-C-1G can replace a DM-TX-4K-100-C-1G in an existing installation (additional programming may be required).

        DM 8G+ Technology
        Engineered for ultra high-bandwidth and ultimate scalability, Crestron DM 8G+ technology transports high-definition video, audio, power, Ethernet, and control signals over twisted pair copper wire. Uncompressed Full HD 1080p, WUXGA, and 2K signals are supported at distances up to 330 ft (100 m) using Crestron DM® Ultra cable, Crestron DM 8G® cable, or third-party CAT5e (or higher). Higher resolution signals up to UHD and 4K are supported at distances up to 330 ft (100 m) using DM Ultra cable, 230 ft (70 m) using DM 8G cable, or 165 ft (50 m) using third-party CAT5e (or higher).2

        HDBaseT Compatibility
        DM 8G+ technology is designed using HDBaseT Alliance specifications, ensuring interoperability with other HDBaseT certified products. Via the DM 8G+ output, the DM-TX-4KZ-100-C-1G can be connected directly to a third-party HDBaseT compliant receiver or display device without requiring a DM receiver.

        Multimedia Computer/AV Interface
        A single HDMI input port is provided on the DM-TX-4KZ-100‑C-1G for connection to a laptop computer, mobile device, or other AV source.3 A single CAT5e (or higher) cable connects the DM-TX-4KZ-100-C-1G to a DM switcher or receiver or to an HDBaseT device. Video, audio, control, networking, and power signals are transported through one RJ-45 connection.2, 4, 5 When used with a DM switcher, multiple DM-TX-4KZ-100-C-1G devices can be installed, enabling several AV input signals at different locations to be transmitted to multiple displays throughout a room or larger facility. When used with a single DM 8G+ receiver/room controller, the DM-TX-4KZ-100-C-1G extends an AV signal to a single display.

        Device Control
        The DM-TX-4KZ-100-C-1G includes built-in IR and RS-232 control ports to enable programmable control of the connected source device via a control system.6 When connected to a control system, the DM-TX-4KZ-100-C-1G also provides a gateway for controlling the AV source through CEC (Consumer Electronics Control) over the HDMI input, potentially eliminating the need for a dedicated serial cable or IR emitter.

        Pass-through mode for RS-232 and CEC is also supported. For additional information, refer to Online Help Answer ID 1000497 on the Crestron website (www.crestron.com).

        Versatile Mounting Options
        The DM-TX-4KZ-100-C-1G is designed to be mounted into a 1‑gang electrical box or plaster ring (not included). Standard gang-box mounting enables installation adjacent to an Ethernet jack (Crestron MP-WP183 or equivalent).7

        Using the included mounting bracket, the DM-TX-4KZ-100‑C-1G can also be attached to a suitable flat surface such as the underside of a table. As an additional mounting option, the DM‑TX-4KZ-100-C-1G can be attached to a single rack rail.

        Power via the DM connection can be used to power the DM‑TX-4KZ-100-C-1G. The device can also be powered using the optional PW-2407WUL wall mount power pack (sold separately).

        For additional design tools and reference documents, refer to the DigitalMedia resources web page at http://www.crestron.com/dmresources.

         
        Key Features
        • 4K60 4:4:4 support
        • HDR10, Deep Color, and 3D video
        • Dolby® TrueHD, Dolby Atmos®, DTS HD®, and uncompressed 7.1 linear PCM audio
        • HDBaseT® compatibility
        • HDCP 2.2 compliance
        • HDMI® input (DVI and Dual-Mode DisplayPort™ interface compatible)
        • DM 8G+® output for connection to a DM® switcher or receiver via a single CAT5e (or higher) twisted pair cable
        • Transmission distance up to 330 ft (100 m) for resolutions up to UHD and 4K using DM Ultra cable
        • Transmission distance up to 330 ft (100 m) for 1080p, WUXGA, and 2K using DM 8G® cable or CAT5e
        • Transmission distance up to 230 ft (70 m) for UHD and 4K using DM 8G cable or up to 165 ft (50 m) using CAT5e
        • Device control via CEC, IR, and RS-232
        • Powered via the DM connection or optional power pack (sold separately)
        • Versatile mounting options including 1-gang electrical box, surface mounting, and attachment to rack rail
        • Surface-mount bracket included
        • Black finish
        1. 4K60 4:4:4 performance and HDR support require the use of HDMI cables and couplers with a minimum TMDS bandwidth of 18 Gbps. If 4K60 4:2:0 or 4K30 4:4:4 performance is acceptable, cables and couplers with a minimum bandwidth of 10.2 Gbps can be used. Bandwidth loss is cumulative; therefore, performance may be reduced when inserting multiple cables and couplers inline.
        2. The maximum cable length for DM 8G+ or HDBaseT transmission is dependent upon the type of cable and resolution of the video signal. Refer to the Maximum Cable Lengths table for information. Crestron legacy cable models DM-CBL and DM-CBL-D support the same resolutions and cable lengths as CAT5e. Shielded cable and connectors are recommended to safeguard against unpredictable environmental electrical noise that may impact performance at resolutions above 1080p. Refer to the Crestron DigitalMedia System Design Guide (Doc. 4546) for additional guidelines. DM 8G+ technology is compatible with the HDBaseT Alliance specifications for connecting to HDBaseT compliant equipment. All wire and cables are sold separately.
        3. The HDMI input requires an appropriate adapter or interface cable to accommodate a DVI or Dual-Mode DisplayPort signal. CBL-HD-DVI interface cables are available separately.
        4.  In order for the DM-TX-4KZ-100-C-1-G to receive PoDM (Power over DigitalMedia), the device must connect to a DM switcher or other equipment that has a PoDM PSE port. Wiring that connects to a PoDM PSE port is for intrabuilding use only.
        5.  In order for the DM-TX-4KZ-100-C-1-G to receive HDBaseT PoE, the device must connect to equipment that has an HDBaseT PoE PSE port. Wiring that connects to an HDBaseT PoE PSE port is for intrabuilding use only.
        6. The IR and RS-232 (COM) ports are enabled only when the DM-TX-4KZ-100-C-1G connects to an Ethernet-enabled DM receiver or switcher that is addressable from a Crestron control system.
        7. The DM-TX-4KZ-100-C-1G does not include an Ethernet port. Local Ethernet connectivity for external devices requires an MP-WP183 or equivalent Ethernet jack with a dedicated LAN connection.

        This product may be purchased from select authorized Crestron dealers and distributors. To find a dealer or distributor, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/How-To-Buy/Find-a-Representative or by calling 855‑263‑8754.

        This product is covered under the Crestron standard limited warranty. Refer to www.crestron.com/warranty for full details.

        The specific patents that cover Crestron products are listed online at patents.crestron.com.

        Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

        Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G, DigitalMedia 8G+, DM, DM 8G, and DM 8G+ are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Dolby, Dolby Atmos, and Dolby Digital are either trademarks or registered trademarks of Dolby Laboratories in the United States and/or other countries. DTS, DTS HD, and DTS HD Master Audio are either trademarks or registered trademarks of DTS, Inc. in the United States and/or other countries. HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. DisplayPort and VESA are either trademarks or registered trademarks of Video Electronics Standards Association in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2020 Crestron Electronics, Inc.

         
        4K HDCP 2.2 HDMI
        Maximum Cable Lengths
         
         
        Resolution        		 Cable Type
        DM-CBL-ULTRA
        DM® Ultra Cable        		 DM-CBL-8G
        DM 8G® Cable        		 Third-Party CAT5e
        (or Higher)2
        1920x1080 FHD 1080p 330 ft (100 m) 330 ft (100 m) 330 ft (100 m)
        1920x1200 WUXGA
        1600x1200 UXGA
        2048x1080 DCI 2K
        2048x1152 QWXGA
        2560x1080 UWFHD 230 ft (70 m) 165 ft (50 m)
        2560x1440 WQHD
        2560x1600 WQXGA
        3840x2160 4K UHD
        Video
        Input Signal Types HDMI with HDR10, Deep Color, 3D, and 4K60 4:4:4 support (DVI and Dual-Mode DisplayPort™ interface compatible)3
        Output Signal Types DM 8G+ and HDBaseT with HDR10, Deep Color, 3D, and 4K60 4:4:4 support
        Copy Protection HDCP 2.2
        Maximum Resolutions The following table lists common resolutions.
        Scan
        Type        		 Resolution Frame
        Rate        		 Color
        Sampling        		 Color
        Depth
        Progressive 3840x2160 4K UHD 24 Hz 4:4:4 36 bit
        30 Hz 4:4:4 36 bit
        60 Hz 4:2:2 36 bit
        60 Hz 4:4:4 24 bit
        2560x1600 WQXGA 60 Hz 4:4:4 36 bit
        1920x1080 HD 1080p 60 Hz 4:4:4 36 bit
        Interlaced 1920x1080 HD 1080i 30 Hz 4:4:4 36 bit
        NOTES:
        • Custom resolutions may be supported at pixel clock rates up to 600 MHz*.
        • Support of 4096x2160 resolutions is limited. For detailed information, refer to Online Help Answer ID 1000497.
        *Due to DSC codec limitations, only 4K60 and 4K50 resolutions can be supported at pixel clock rates between 300-600MHz. For detailed information, refer to Online Help Answer ID 1001200.
        Audio
        Input Signal Types HDMI (Dual-Mode DisplayPort interface compatible)3
        Output Signal Types DM 8G+, HDBaseT
        Formats Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby® TrueHD, Dolby Atmos®, DTS®, DTS ES, DTS 96/24, DTS-HD® High Res, DTS HD Master Audio™, DTS:X, LPCM up to 8 channels
        Communications
        RS-232 2-way device control and monitoring up to 115.2k baud with software handshaking via control system
        IR/Serial 1-way device control via infrared up to 1.1 MHz or serial TTL/RS-232 (0-5 V) up to 19.2k baud via control system
        DigitalMedia DM 8G+, HDCP 2.2, EDID, CEC, PoDM
        HDBaseT HDCP 2.2, EDID, CEC, PoE
        HDMI HDCP 2.2, EDID, CEC
        Connectors, Front
        HDMI IN (1) 19-pin Type A connector, female;
        HDMI digital video/audio input
        (DVI and Dual-Mode DisplayPort interface compatible)3
        IR OUT (1) 2-pin 3.5 mm detachable terminal block;
        IR/Serial port;2
        IR output up to 1.1 MHz;
        1-way serial TTL/RS-232 (0-5 V) up to 19200 baud
        COM (1) 3-pin 3.5 mm detachable terminal block;
        Bidirectional RS-232 port;2
        Up to 115.2k baud, software handshaking support
        Connectors, Rear
        G (1) 6-32 screw;
        Chassis ground lug
        DM OUT (1) 8-pin RJ-45 female, shielded;
        DM 8G+ output, HDBaseT standard compliant;
        PoDM PD (Powered Device) port (HDBaseT PoE compatible);4, 5
        Connects to the DM 8G+ input of a DM switcher, receiver, or other DM device or to an HDBaseT device via CAT5e, Crestron DM-CBL-8G, or Crestron DM-CBL-ULTRA cable2
        24VDC 0.75A (1) 2-pin 3.5 mm detachable terminal block;
        24 VDC power input;
        PW-2407WUL power pack sold separately
        Indicators
        POWER (1) Green LED, indicates operating power supplied via PoDM, HDBaseT PoE, or local power pack
        VIDEO (1) Green LED, indicates video signal presence at the HDMI input
        DM OUT (rear) (2) LEDs, green LED indicates DM link status, amber LED indicates video and HDCP signal presence
        Power
        Power over DM (PoDM) IEEE 802.3at Type 1 Class 3 (12.95 W) compliant PoDM PD, capable of being powered by PoDM PSE (Power Sourcing Equipment)4
        Power over HDBaseT IEEE 802.3at Type 1 Class 3 (12.95 W) compliant HDBaseT PoE PD (Powered Device), capable of being powered by an HDBaseT PoE PSE (Power Sourcing Equipment)5
        Power Pack (Optional) Input: 100-240 VAC, 50/60 Hz;
        Output: 0.75 A @ 24 VDC;
        Model: PW-2407WUL (sold separately)
        Power Consumption With PoDM or HDBaseT PoE:
           5.43 W typical
           3.25 W idle
        With 24 VDC:
           5.55 W typical
           3.31 W idle
        Environmental
        Temperature 32° to 95° F (0° to 35° C)
        Humidity 10% to 90% RH (non-condensing)
        Heat Dissipation With PoDM or HDBaseT PoE:
           18.53 BTU/hr typical
           11.09 BTU/hr idle
        With 24 VDC:
           18.94 BTU/hr typical
           11.29 BTU/hr idle
        Enclosure
        Construction Metal with white or black polycarbonate label overlay on front panel
        Flush Wall Mount Mounts in 1-gang 2-1/8 in. deep electrical box or plaster ring (not included), decorator style faceplate sold separately
        Surface Mount Surface-mount bracket included
        Rack Mount Attaches to a single 19-inch EIA rack rail
        Dimensions
        Height 4.11 in. (105 mm)
        Width 1.72 in. (44 mm)
        Depth 2.20 in. (56 mm)
        Weight
        8 oz (227 g)
        Compliance
        ETL (Intertek), CE, IC, FCC Part 15 Class B digital device
        Click here to search product certificates.
        1. 4K60 4:4:4 performance and HDR support require the use of HDMI cables and couplers with a minimum TMDS bandwidth of 18 Gbps. If 4K60 4:2:0 or 4K30 4:4:4 performance is acceptable, cables and couplers with a minimum bandwidth of 10.2 Gbps can be used. Bandwidth loss is cumulative; therefore, performance may be reduced when inserting multiple cables and couplers inline.
        2. The maximum cable length for DM 8G+ or HDBaseT transmission is dependent upon the type of cable and resolution of the video signal. Refer to the Maximum Cable Lengths table for information. Crestron legacy cable models DM-CBL and DM-CBL-D support the same resolutions and cable lengths as CAT5e. Shielded cable and connectors are recommended to safeguard against unpredictable environmental electrical noise that may impact performance at resolutions above 1080p. Refer to the Crestron DigitalMedia System Design Guide (Doc. 4546) for additional guidelines. DM 8G+ technology is compatible with the HDBaseT Alliance specifications for connecting to HDBaseT compliant equipment. All wire and cables are sold separately.
        3. The HDMI input requires an appropriate adapter or interface cable to accommodate a DVI or Dual-Mode DisplayPort signal. CBL-HD-DVI interface cables are available separately.
        4.  In order for the DM-TX-4KZ-100-C-1-G to receive PoDM (Power over DigitalMedia), the device must connect to a DM switcher or other equipment that has a PoDM PSE port. Wiring that connects to a PoDM PSE port is for intrabuilding use only.
        5.  In order for the DM-TX-4KZ-100-C-1-G to receive HDBaseT PoE, the device must connect to equipment that has an HDBaseT PoE PSE port. Wiring that connects to an HDBaseT PoE PSE port is for intrabuilding use only.
        6. The IR and RS-232 (COM) ports are enabled only when the DM-TX-4KZ-100-C-1G connects to an Ethernet-enabled DM receiver or switcher that is addressable from a Crestron control system.
        7. The DM-TX-4KZ-100-C-1G does not include an Ethernet port. Local Ethernet connectivity for external devices requires an MP-WP183 or equivalent Ethernet jack with a dedicated LAN connection.

        This product may be purchased from select authorized Crestron dealers and distributors. To find a dealer or distributor, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/How-To-Buy/Find-a-Representative or by calling 855‑263‑8754.

        This product is covered under the Crestron standard limited warranty. Refer to www.crestron.com/warranty for full details.

        The specific patents that cover Crestron products are listed online at patents.crestron.com.

        Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

        Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G, DigitalMedia 8G+, DM, DM 8G, and DM 8G+ are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Dolby, Dolby Atmos, and Dolby Digital are either trademarks or registered trademarks of Dolby Laboratories in the United States and/or other countries. DTS, DTS HD, and DTS HD Master Audio are either trademarks or registered trademarks of DTS, Inc. in the United States and/or other countries. HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. DisplayPort and VESA are either trademarks or registered trademarks of Video Electronics Standards Association in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2020 Crestron Electronics, Inc.

        Pricing Region Select
        Please select your region below to see the appropriate Advertised Pricing.