Online Help

Products

    Pages

        Master Photo: HD-TX-201-C-2G-E-W-T: Front with faceplate
        Add to Favorites

        HD-TX-201-C-2G-E-W-T

        DM Lite® Transmitter and 2x1 Auto-Switcher for HDMI®, VGA, and Analog Audio Signal Extension over CATx Cable, Wall Plate, White Textured

        Limited Supply Available

        Pairs with a DM Lite® or DMPS Lite™ receiver to provide a signal extender for HDMI® signals up to UHD and 4K. Provides auto-switching HDMI, VGA, and stereo analog audio inputs.

        Have a question?
        Add to a Project
        Find a Dealer

        The HD-TX-201-C-2G-E (-B-T or -W-T) is a DM Lite® wall plate transmitter designed to pair with a DM Lite or DMPS Lite™ receiver to form a signal extender for HDMI® signals. The DM Lite family of products offers a versatile solution for extending HD, UHD, 2K, and 4K video signals, with stereo or surround sound audio, over a single CAT5e (or higher) cable. A cable length of up to 230 ft (70 m) is supported for HD 1080p, WUXGA, and 2K signals, or up to 130 ft (40 m) for UHD and 4K.1

        In addition to its HDMI input, the HD-TX-201-C-2G-E also includes a VGA input accompanied by a stereo analog audio input. Auto-switching between HDMI and VGA enables plug-and-play simplicity. Manual input selection is also available using the front panel INPUT SEL button. The VGA input can accept RGB and component video signals by using an appropriate breakout cable or adapter (not included). The audio input is selected in tandem with the VGA input, and can be used by itself with no video source connected. However, it cannot be paired with the HDMI video input.

        NOTE: When paired with an HD-RX-201-C-E or DMPS Lite receiver, the local inputs are switched in combination with the HDMI input on the receiver, and can also be controlled remotely through integration with a Crestron® control system.

        A CAT6a RJ-45 courtesy jack is included to provide a 1000BASE-T network connection for computers and other devices. The front panel jack passes through to a parallel jack on the rear, which connects to an available port on the customer’s LAN. This LAN jack is provided as a convenience to replace the need for a separate RJ-45 wall jack. It does not interface with the DM Lite system and cannot be used to extend Ethernet signals or interface with a control system.

        The HD-TX-201-C-2G-E series is available in black or white, and is designed to mount into a 2-gang electrical box or plaster ring (not included). When paired with a surface-mountable receiver, the HD-TX-201-C-2G-E is powered by the receiver over the DM Lite link cable.2

        Note: This product is not addressable from a control system and offers no programmable functionality except when paired with an HD-RX-201-C-E or DMPS Lite receiver. Otherwise, AV and CEC signals are simply passed through between the transmitter and receiver. The RJ-45 link port on this product is exclusively intended for linking with a single DM Lite or DMPS Lite receiver. It should not be used to connect to any other equipment or network. DM Lite technology is not compatible with PoE, PoDM, DigitalMedia 8G+®, or HDBaseT® technology.

         
        Key Features
        • Pairs with a DM Lite® or DMPS Lite™ receiver
        • Enables extension of HDMI® video and audio signals
        • Converts and extends VGA and analog audio signals
        • Auto-switches between one HDMI input and one VGA input
        • Links to the receiver via a single CAT5e (or higher) twisted pair cable
        • Supports 4K and UHD at up to 130 ft (40 m)
        • Supports HD 1080p, WUXGA, and 2K at up to 230 ft (70 m)
        • Handles 4K video resolutions up to 4K60 4:2:0 and 4K30 4:4:4
        • Handles 3D video and Deep Color
        • Supports Dolby® TrueHD, Dolby Atmos®, DTS HD®, DTS:X®, and uncompressed 7.1 linear PCM audio
        • Compatible with HDMI, DVI, and Dual-Mode DisplayPort™ sources
        • Compatible with VGA, RGBHV, RGBS, RGsB, and YPbPr component sources up to HD 1080p and WUXGA
        • HDCP 1.4 compliant
        • Passes CEC and EDID signals
        • Allows control system integration when paired with an HD-RX-201-C-E or DMPS Lite receiver
        • Courtesy LAN jack
        • Flush wall mount design
        • Installs in a 2-gang U.S. electrical box (2-1/4” deep) or plaster ring (not included)
        • Decorator style faceplates sold separately (type FP-G2-DM only)
        • Normally powered by the receiver (surface-mountable) over the link cable
        1. For the DM Lite link cable, use Crestron DM-CBL-8G DigitalMedia 8G™ cable, Crestron DM-CBL-ULTRA DigitalMedia™ Ultra cable, or third-party CAT5e or higher. The maximum cable length is 230 ft (70 m) for resolutions up to 2K or 130 ft (40 m) for higher resolution signals up to 4K. Refer to the “Maximum DM Lite Link Cable Lengths” table for a more detailed overview. Shielded cable and connectors are required when bundling multiple cables in a wire run, and are recommended for all applications to safeguard against unpredictable environmental electrical noise which may impact performance at resolutions above 1080p. Wire and cables are sold separately. DM Lite devices are not compatible with DigitalMedia 8G+, HDBaseT, PoE, PoDM, or any other CATx based interface or network.
        2. When connecting a wall plate transmitter to a surface-mountable receiver, use the power pack that ships with the receiver. If the transmitter and receiver are both wall plates, a separate power pack must be purchased, which may be connected to either the transmitter or receiver. Only one power pack is required. Do not connect more than one power pack. Please note, the wall plate compatible power pack is not yet available. Please contact Crestron Customer Support for assistance when pairing a wall plate transmitter with a wall plate receiver. DM Lite devices are not compatible with PoE or PoDM. DM Lite devices are not compatible with PoE or PoDM.
        3. The HDMI input requires an appropriate adapter or interface cable to accommodate a DVI or Dual-Mode DisplayPort signal. CBL-HD-DVI interface cables are available separately.
        4. The VGA input requires an appropriate breakout cable or adapter to accommodate an RGB or component video signal.

        This product may be purchased from select authorized Crestron dealers and distributors. To find a dealer or distributor, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/How-To-Buy/Find-a-Representative or by calling 855-263-8754.

        This product is covered under the Crestron standard limited warranty. Refer to www.crestron.com/warranty for full details.

        The specific patents that cover Crestron products are listed online at patents.crestron.com.

        Certain Crestron products contain open source software. For specific information, visit https://www.crestron.com/opensource.

        Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G, DigitalMedia 8G+, DM, DM 8G, DM Lite, and DMPS Lite are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Dolby, Dolby Atmos, and Dolby Digital are either trademarks or registered trademarks of Dolby Laboratories in the United States and/or other countries.  DTS, DTS HD, and DTS:X are either trademarks or registered trademarks of DTS, Inc. in the United States and/or other countries. HDBaseT is either a trademark or registered trademark of HDBaseT Alliance in the United States and/or other countries. HDMI and the HDMI Logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. DisplayPort is either a trademark or registered trademark of Video Electronics Standards Association in the United States and/or other countries. UL is either a trademark or registered trademark of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2020 Crestron Electronics, Inc.

         
        4K
        Video
        Switcher 2x1 manual or auto-switching, audio-follow-video
        Input Signal Types HDMI with Deep Color, 3D, and 4K (DVI and Dual-Mode DisplayPortTM interface compatible3), VGA/RGB (RGBHV, RGBS, RGsB), component (YPbPr)4
        Copy Protection HDCP 1.4
        Maximum Resolutions
        Input
        Type        		 Scan
        Type        		 Resolution Frame
        Rate        		 Color
        Sampling        		 Color
        Depth
        HDMI Progressive 4096x2160 DCI 4K
        &
        3840x2160 4K UHD        		 24 Hz 4:4:4 30 bit
        30 Hz 4:4:4 24 bit
        30 Hz 4:2:2 36 bit
        60 Hz 4:2:0 24 bit
        2560x1600 WQXGA 60 Hz 4:4:4 36 bit
        1920x1080 HD 1080p 60 Hz 4:4:4 36 bit
        Interlaced 1920x1080 HD 1080i 30 Hz 4:4:4 36 bit
        VGA/RGB Progressive 1600x1200 UXGA 60 Hz n/a
        1920x1200 WUXGA 60 Hz n/a
        Component Progressive 1920x1080 HD 1080p 60 Hz n/a
        Interlaced 1920x1080 HD 1080i 30 Hz n/a
        NOTE: Common resolutions are shown; other custom resolutions are supported at pixel clock rates up to 300 MHz for HDMI or 165 MHz for VGA.
        Audio
        Input Signal Types HDMI (Dual-Mode DisplayPort interface compatible3), analog stereo
        Digital Formats Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS®, DTS ES, DTS 96/24, DTS HD High Res, DTS-HD Master Audio, DTS:X, LPCM up to 8 channels
        Analog Formats Stereo 2-channel
        Analog-To-Digital Conversion 24-bit 48 kHz
        Analog Performance Frequency Response: 20 Hz to 20 kHz ±0.75 dB;
        S/N Ratio: >90 dB, 20 Hz to 20 kHz A-weighted;
        THD+N: <0.006% @ 1 kHz;
        Stereo Separation: >80 dB
        Communications
        HDMI HDCP 1.4, EDID, CEC pass-through
        DM Lite Link Proprietary link for connection between one DM Lite transmitter and receiver only
        NOTE: Supports management of HDCP and EDID only when paired with an HD-RX-201-C-E or DMPS Lite receiver; supports management of CEC between the connected HDMI device and a control system only when paired with an HD-RX-201-C-E or DMPS Lite receiver.
        Connectors
        HDMI IN (1) HDMI Type A connector, female;
        HDMI digital video/audio input (DVI and Dual-Mode DisplayPort interface compatible3)
        VGA IN (1) HD15 connector, female;
        RGB (VGA) or component video input4;
        Formats: RGBHV, RGBS, RGsB, and YPbPr
        AUDIO IN (1) 3.5 mm TRS mini phone jack;
        Unbalanced stereo line-level audio input;
        Maximum Input Level: 2 Vrms;
        Input Impedance: 44k Ohms
        LAN (Front) (1) 8-pin RJ-45 connector, female;
        Passive pass-through to the rear panel LAN jack;
        See "LAN (Rear)" specifications below
        SERVICE (Right Side) (1) USB Type A connector, female;
        For factory use only
        TO RX (DM Lite, Rear) (1) 8-pin RJ-45 connector, female, shielded;
        DM Lite link port for connection to a DM Lite or DMPS Lite receiver1
        24VDC 1.25A (Rear) (2) Captive screw terminals;
        24 VDC power input;
        Power pack sold separately (if required, model TBA)2;
        NOTE: This connection powers both the transmitter and receiver; this connection is not normally used when pairing with a surface-mountable receiver.2
        LAN (Rear) (1) 8-pin RJ-45 connector, female;
        Passive pass-through to the front panel LAN jack;
        Compatible Cable Standards: CAT5e, CAT6, and CAT6a;
        Low Level Contact Resistance: 100 mΩ maximum;
        Insulation Resistance: 500 mΩ minimum at 500 VDC;
        Dielectric Withstanding Voltage: 1000 VAC between contacts and shell;
        Voltage Rating: 125 VAC;
        Current Rating: 1.5 Amps;
        PoE Compatibility: IEEE 802.3at PoE and PoE+;
        Insertion Force: 22 N maximum;
        Retention Force: 76 N minimum
        Controls and Indicators
        PWR (1) Bi-color green/amber LED, indicates operating power is supplied from the receiver via the DM Lite link or from a power pack via the 24 VDC input, turns amber while booting and green when operating
        HDMI IN (1) Bi-color green/amber LED, indicates HDMI input selection and signal presence
        VGA IN (1) Bi-color green/amber LED, indicates VGA input selection and signal presence
        INPUT SEL (1) Push button for manual input selection, cycles through all available inputs on both the transmitter and receiver
        AUTO (1) Push button to enable/disable auto-switching mode, and (1) green LED to indicate auto-switching mode is enabled
        SETUP (1) Red LED and (1) recessed push button for Ethernet setup (only when paired with an HD-RX-201-C-E or DMPS Lite receiver)
        LINK (1) Green LED, indicates the DM Lite link status
        RESET (1) Push button for hardware reset (Resets both the transmitter and receiver when paired with an HD-RX-201-C-E or DMPS Lite receiver)
        TO RX (DM Lite, Rear) (2) LEDs on RJ-45 connector, green LED indicates DM Lite link status, amber LED indicates a valid video signal
        Power
        Power Pack (sold separately) Input: 100-240 VAC, 50/60 Hz;
        Output: 1.25 Amps @ 24 VDC;
        Model: TBA
        Note: This power pack is required only when the HD-TX-201-C-2G-E is paired with a wall plate receiver. When the HD-TX-201-C-2G-E is paired with a surface-mountable receiver, the power pack included with and connected to the receiver is used to power both the receiver and the HD-TX-201-C-2G-E.2
        Environmental
        Temperature 32° to 104° F (0° to 40° C)
        Humidity 20% to 90% RH (non-condensing)
        Heat Dissipation 20.1 BTU/hr
        Construction
        Composition Metal housing and bracket with black or white polycarbonate front label overlays
        Mounting Mounts in a 2-gang, 2-1/4 inch (57 mm) deep U.S. electrical box or plaster ring (not included)
        Faceplate Requires a Crestron FP-G2-DM-B-T or FP-G2-DM-W-T faceplate (sold separately, other faceplates are incompatible)
        Dimensions
        Height 4.19 in (107 mm)
        Width 3.50 in (89 mm)
        Depth 2.07 in (53 mm)
        Weight
        8.9 oz (252 g)
        Compliance
        UL® Listed for US and Canada, CE, IC, FCC Part 15 Class B digital device
        Regulatory Models HD-TX-201-C-2G-E-B-T, HD-TX-201-C-2G-E-W-T
        Maximum DM Lite Link Cable Lengths
         
         
        Resolution        		 Cable Type
        CAT5e (or higher),
        DM-CBL-ULTRA DM® Ultra Cable, or
        DM-CBL-8G DM 8G DM 8G® Cable1
        1920x1080 FHD 1080p 230 ft (70 m)
        1920x1200 WUXGA
        1600x1200 UXGA
        2048x1080 DCI 2K
        2048x1152 QWXGA
        2560x1080 UWFHD 130 ft (40 m)
        2560x1440 WQHD
        2560x1600 WQXGA
        3840x2160 4K UHD
        4096x2160 DCI 4K
        Click here to search product certificates.
        1. For the DM Lite link cable, use Crestron DM-CBL-8G DigitalMedia 8G™ cable, Crestron DM-CBL-ULTRA DigitalMedia™ Ultra cable, or third-party CAT5e or higher. The maximum cable length is 230 ft (70 m) for resolutions up to 2K or 130 ft (40 m) for higher resolution signals up to 4K. Refer to the “Maximum DM Lite Link Cable Lengths” table for a more detailed overview. Shielded cable and connectors are required when bundling multiple cables in a wire run, and are recommended for all applications to safeguard against unpredictable environmental electrical noise which may impact performance at resolutions above 1080p. Wire and cables are sold separately. DM Lite devices are not compatible with DigitalMedia 8G+, HDBaseT, PoE, PoDM, or any other CATx based interface or network.
        2. When connecting a wall plate transmitter to a surface-mountable receiver, use the power pack that ships with the receiver. If the transmitter and receiver are both wall plates, a separate power pack must be purchased, which may be connected to either the transmitter or receiver. Only one power pack is required. Do not connect more than one power pack. Please note, the wall plate compatible power pack is not yet available. Please contact Crestron Customer Support for assistance when pairing a wall plate transmitter with a wall plate receiver. DM Lite devices are not compatible with PoE or PoDM. DM Lite devices are not compatible with PoE or PoDM.
        3. The HDMI input requires an appropriate adapter or interface cable to accommodate a DVI or Dual-Mode DisplayPort signal. CBL-HD-DVI interface cables are available separately.
        4. The VGA input requires an appropriate breakout cable or adapter to accommodate an RGB or component video signal.

        This product may be purchased from select authorized Crestron dealers and distributors. To find a dealer or distributor, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/How-To-Buy/Find-a-Representative or by calling 855-263-8754.

        This product is covered under the Crestron standard limited warranty. Refer to www.crestron.com/warranty for full details.

        The specific patents that cover Crestron products are listed online at patents.crestron.com.

        Certain Crestron products contain open source software. For specific information, visit https://www.crestron.com/opensource.

        Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G, DigitalMedia 8G+, DM, DM 8G, DM Lite, and DMPS Lite are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Dolby, Dolby Atmos, and Dolby Digital are either trademarks or registered trademarks of Dolby Laboratories in the United States and/or other countries.  DTS, DTS HD, and DTS:X are either trademarks or registered trademarks of DTS, Inc. in the United States and/or other countries. HDBaseT is either a trademark or registered trademark of HDBaseT Alliance in the United States and/or other countries. HDMI and the HDMI Logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. DisplayPort is either a trademark or registered trademark of Video Electronics Standards Association in the United States and/or other countries. UL is either a trademark or registered trademark of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2020 Crestron Electronics, Inc.

        Pricing Region Select
        Please select your region below to see the appropriate Advertised Pricing.